prod-tilt_mount_2020mini_th_s

Tilt Mount

For: 20/20 series

The Tilt Mounting Brackets allow accurate directional selection of the detector for optimum area coverage. These brackets movement ensure maximum effectiveness and accurate location of the detector's coverage area.

PN 20/20-005

air_shield_777650_high-r1-170526

Air Shield

For: 40/40 series

The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

PN 777650



fs-1100_high-r1-170526

FS Series Flame Simulator

For: 40/40, 20/20, 20/20M Series

The SharpEye Series Flame Simulator is the essential complimentary tool to the self-testing capabilities of Sharpeye Flame Detectors. It brings fire prevention safety to a higher level by giving you the ability to fully test the operational readiness of your entire fire detection system.

The following models are available:

  • FS-1100 - IR3 detectors
  • FS-1200 - UV and UV/IR detectors
  • FS-1300 - Single IR detectors
  • FS-1400 - Multi IR detectors
SharpEye Model FS-1100 Triple IR3 Flame Simulator User Guide
|English |
Russian
SharpEye Model FS-1200 UV/IR Flame Simulator User Guide
|English |
Russian
SharpEye Model FS-1300 Single IR Flame Simulator User Guide
|English |
Russian
SharpEye Model FS-1400 Multi IR Flame Simulator  User Manual
|English | 
Russian


pointer_4040_high-r1-170526

Cone Viewer

For: 40/40 series

Does the detector cover the area that needs protection? Is it located correctly and does the detector’s cone of vision cover the most dangerous spot? The answer - use the Cone Viewer that designates the optical flame detector’s area of coverage (cone of vision) on-site at the specific installation. This accessory enables the designer/installer to optimize detector location and its actual detection area coverage.

PN 777166

duct-mount_4040_high-r1-170526

Duct Mount

For: 40/40 series

The Duct Mount allows flame detection in areas where high temperatures exist or in cases where the detector cannot be installed inside the area. It comprises a special duct mount arrangement with specific optical window to allow installation in high temperature duct applications. The mount can be used with all Spectrex 40/40 Series flame detectors.

PN 777670


laptop_kit_4040_high-r1-170526

Mini Laptop Kit

For: 40/40, 20/20, 20/20M series

The mini laptop, pre-loaded with Spectrex software, enables the user to re-configure settings or perform diagnostics on all Spectrex flame and gas detectors. The kit includes cable harness with RS485/232 converter. The mini laptop is programmed with maintenance winhost for all detector types. 

PN 777820

pole-mount_4040_high-r1-170526

U-Bolt / Pole Mount

For: 40/40 series

The U-bolt mount is available to facilitate either 2” or 3” pipe mounting.

Material: Stainless steel

PN 789260-1 -  Pipe 3” Version
PN 789260-2 - Pipe 2” Version

usb_rs485_4040_high-r1-170526

USB RS485 Harness

For: 20/20 series

The USB RS485 Harness Kit with RS485/232 converter, used with Spectrex Host software, enables the user to connect to any available PC or laptop to re-configure settings or perform diagnostics on all 40/40 series flame detectors. 

P/N 794079-3 for 20/20SH, SI, CTIx, MI, ML
P/N 794079-5 for 40/40 Series
P/N 794079-6 for 20/20SI SIL Series

weather_shield_4040_high-r1-170526

Weather Protector

For:  40/40 series

The Weather Protector is designed to protect the detector from rain and snow and direct extreme temperatures from the sun. 

PN 777163 Stainless steel, red epoxy
PN 777263 Plastic (ABS conductive), red

prod-air_shield_20

Air Shield

For: 20/20 series

The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

PN 20/20-787

prod-laser_aimer_2020m_th_s_600x575

Laser Aimer

For: 20/20 series

Does the optical detector cover the entire hazardous area that needs protection? Has the installer located the detector at the right location and does the detector's cone of vision cover the most dangerous spot?

These questions can be answered with the use of a simple tool -- the Laser Detection Area Coverage Pointer that designates the optical flame detector's area of coverage (cone of vision) on-site at the specific installation. This add-on acessory enables the designer and installer to optimize the detector's location and teh actual detection area coverage of each installed detector.

PN 787969

prod-rain_cover_4040m_th_s

Rain Cover

For: 40/40 series

The Rain Cover is designed to protect the detector from rain and snow.

PN 787980

Please enable JavaScript to use this website.